Skip to content

DecoderDumper

Quite often, a programmer needs to express bytes, or more structured data in a textual format for inspection, or debugging. The DecoderDumper package is a framework for doing just that. The package contains a couple of dumpers of which the HexDumper is the most used. With the HexDumper a hexadecimal dump of an array of bytes is created with a minimum of code like:

byte[] bytes = new byte[] { 10, 20, 0x04, (byte) 0xff, 'a', 'b', 'c', 'd', 'e', 'f', 'g', 'h', 'i', 'j', 'k', 'l', 'm' };
System.out.println(HexDumper.hexDumper(bytes));

This outputs:

00000000: 0a 14 04 ff 61 62 63 64  65 66 67 68 69 6a 6b 6c  ....abcd efghijkl
00000010: 6d                                                m                

By default, the address of the first byte is 0. This can be overridden by explicitly setting the start address like:

System.out.println(HexDumper.hexDumper(123, bytes));

Which outputs:

00000070:                                   0a 14 04 ff 61              ....a
00000080: 62 63 64 65 66 67 68 69  6a 6b 6c 6d              bcdefghi jklm    

No lines are output for addresses below the initial offset of 123. The first output line starts with address 00000070 (112 decimal). Then 11 placeholders are output for bytes 112 up to 122 and the first byte of bytes is output in the 12th position of the line with address 00000070.

If the output needs to be sent to some stream, a Dumper must be explicitly instantiated and then manipulated to change the output device. Output is buffered until a line is complete, or until the user explicitly forces all buffered data to be output.

byte[] bytes = new byte[] { 10, 20, 0x04, (byte) 0xff, 'a', 'b', 'c', 'd', 'e', 'f', 'g', 'h', 'i', 'j', 'k', 'l', 'm' };
HexDumper hexDumper = new HexDumper();
hexDumper.setOutputStream(System.err); // from now on, all output is sent to the error output
hexDumper.append(bytes); // will output the first complete line; buffer byte 17 as first byte of the next output line
System.err.println("before flush");
hexDumper.flush(); // force buffered output to printed
System.err.println("adding more data");
byte[] moreBytes = new byte[] { -1, -2, -3, -4, -5, -6, -7, -8, -9, -10, -11, -12, -13, -14, -15, -16, -17 };
hexDumper.append(moreBytes); // will output complete line with gap for previously output data and buffer two bytes
System.err.println("before 2nd flush");
hexDumper.flush(); // force the two buffered bytes to be output

This will output seven lines (on the System.err OutputStream):

00000000: 0a 14 04 ff 61 62 63 64  65 66 67 68 69 6a 6b 6c  ....abcd efghijkl
before flush
00000010: 6d                                                m                
adding more data
00000010:    ff fe fd fc fb fa f9  f8 f7 f6 f5 f4 f3 f2 f1   ....... ........
before 2nd flush
00000020: f0 ef                                             ..               

Dumpers can easily be created for any output format and any data type. Each Dumper has a list of decoders. At run time, input data (the bytes that are to be decoded) is fed, one byte at a time, to all those decoders in sequence. Each decoder is responsible for constructing its own part of an output line. When any of the decoders signals that an output line must be emitted, the Dumper will collect the constructed output from each of the decoders, concatenate it and output the result (unless suppression of multiple output lines with identical data is on and this output line matches the preceding output line). Six decoders are used in the HexDumper in this order: * HexAddressDecoder(16) * FixedString(": ") * HexDecoder(16, 8) * FixedString(" ") * CharDecoder(16, 8) * FixedString("\n");

The simplest one of these is the FixedString decoder. This decoder outputs a fixed part into output line. Three FixedString decoders are used in the HexDumper. The HexAddressDecoder is only slightly more complex. it prints the 8 hexadecimal digit address at the start of each output line. The HexDecoder expresses a byte as two hexadecimal digits plus a trailing space. The CharDecoder outputs a printable byte as the corresponding character, all other bytes as a dot (.). The HexDecoder and CharDecoder take two arguments in their constructors. The first specifies the maximum number of bytes that can be output in one line of output. The second argument specifies that an extra space is to be inserted every n positions.

Each decoder implements the Decoder interface. This interface specifies that a Decoder shall implement four methods:

    String getResult();
    int getMaximumWidth();
    boolean append(int address, byte theByte) throws IOException;
    boolean ignoreForIdenticalOutputCheck();

The getResult method returns a String that is either zero length (if no data was appended), or the length of the maximum output width of the decoder (as reported by the next method). If some bytes have been appended, but the the result under construction is not yet completely filled, the positions reserved for the missing bytes must be filled with spaces. After a call to getResult the internal buffer is reset to zero length.

The getMaximumWidth method returns the width of an output line.

The append method processes one byte. Arguments of this methods are address (the accumulated address which is equal to the initial offset plus the number of bytes processed before this call) and theByte (the byte that must be appended). This method must return true if the accumulated output should be flushed (for most decoders this happens when the last position of the output line under construction has been filled).

The ignoreForIdentialOutputCheck method indicates whether the output of this Decoder is to be used in the test that suppressed output lines with the same content. Decoders that output theByte in some form should report true; other decoders (that have fixed output, or output that only depends on the address parameter of their append method) should report false.

Suppression of multiple lines with the same data is implemented in the Dumper class. It is on by default, but can be switched off (and on again) by calling the setSuppressMultipleIdenticalLines method.

Other dumpers

Besides the HexDumper a Base64Dumper is provided. As the name suggest, this dumper takes bytes that expected to be base64 encoded data and converts that into a human readable form. Some bytes are invalid in base64 encoded data. If one such byte is encountered, the decoder emits a complaint using the CategoryLogger but otherwise continues to attempt to decode the provided data. Base64 encoded data ends with a byte with value 61 (0x3D, =). After encountering such a byte, no further data is decoded (i.e., the Base64Decoder does not handle multiple base64 encoded objects in its input).

The djutils-serialization project contains the SerialDataDumper that can decode the serialized data into a somewhat human readable form. As the objects in the input of that Dumper may differ wildely in size, this dumper has some extra complexitiy that outputs larger objects using multiple output lines while ensuring that all those output lines fit within a reasonable output line size.